inconel 713lc turbine blade

Solidification behavior of inconel 713LC gas turbine ...

Inconel-713LC is a low carbon (LC) nickel-based superalloy, generally produced by investment casting, which is widely used in hot section components of gas turbines engines.

Inconel 713 | Inconel 713C | IN713C | Alloy 713LC | UNS ...

Inconel 713C offers outstanding resistance to thermal fatigue and good castability while offering exceptional rupture strength at 1700°F (927°C). Inconel 713C is a nickel-chromium alloy that is ideally suited for jet engine gas turbine blades.

Mechanical behaviour of Inconel 713LC at different strain ...

Keywords: high strain rate, impact, numerical simulation. 1 Introduction In the rare but possible event of a turbine blade or fan blade failure, the engine must ensure the containment of it.

Solidification behavior of Inconel 713LC gas turbine blades

Inconel is a superalloy of nickel that is comprised of chromium and iron, and portrays excellent resistance to corrosion at high temperatures. Inconel-713LC is a low carbon nickel-based superalloy, generally produced by investment casting, which is widely used in hot section components of gas turbines engines.

Inconel 713LC turbine blade - wfylzz.en.alibaba

Single crystal blade we use PWA 1483 locomotive turbocharger parts vacuum turbine w Service Industrial: gas turbine, steam turbine parts, oil, gas, chemical parts,.[PDF]

alloy INCONEL 713LC after heat treatment Structural ...

structure of castings made of nickel super-alloy NICKEL 713LC after various variants of heat treatment. 2. Used material and experimental technique We have used for experimental investigation castings made of commercially produced nickel super-alloy INCONEL 713LC. Chemical composition of the used melt is given in the Table 1.

Inconel 713lc Casting Parts - alibaba

Inconel 713lc Casting Parts , Find Complete Details about Inconel 713lc Casting Parts,Inconel 713lc Casting Parts,Inconel 713lc Casting Parts,Inconel 713lc Casting Parts from Machinery Engine Parts Supplier or Manufacturer-Shandong Yili Power Technology Co., Ltd.[PDF]

alloy INCONEL 713LC after heat treatment Structural ...

Purpose: Aircraft industry often uses nickel super-alloys for blades of jet engine turbines. This paper summarises analysis of influence of heat treatment on structural characteristics of nickel super-alloy INCONEL 713LC. Design/methodology/approach: Experimental investigation castings made of commercially produced nickel super-alloy INCONEL 713LC.

Inconel 713lc Casting Parts - alibaba

Inconel 713lc Casting Parts , Find Complete Details about Inconel 713lc Casting Parts,Inconel 713lc Casting Parts,Inconel 713lc Casting Parts,Inconel 713lc Casting Parts from Machinery Engine Parts Supplier or Manufacturer-Shandong Yili Power Technology Co., Ltd.

Inconel 713LC Turbine Wheel - yilicast

Inconel 713LC turbine wheel. High quality turbine wheels produce with many years produce experience , the quality control strict according with the ISO 9001-2008. This kinds turbine wheels have exported to America , Germany , Italy ,Greece ect .[PDF]

Mechanical behaviour of Inconel 713LC at different …

this research the study is focused on a blade alloy of Inconel 713LC produced by casting. This is a ... This work is aimed to obtain the mechanical behaviour of the Inconel 713 Low Carbon turbine

Failure analysis of a gas turbine blade made of Inconel ...

Background The blade under evaluation was the first stage blade of a 70 MW combustion turbine with gas inlet tem- perature of 1086 °C. The evaluation was carried out after 24,000 h of blade operation period in mode of base load.[PDF]

Nickel-Based Superalloys for Advanced Turbine Engines ...

mulation at high temperatures, the blades in the early stages of the turbine are typically single crystals, whereas the blades in the later (cooler) stages of the turbine are fabricated from equiaxed alloys. ... IN-713LC 12.0 — 4.5 — — — 2.0 5.9 0.6 — 0.05 0.01 — 0.10 — ...Published in: Journal of Propulsion and Power · 2006Authors: Tresa M Pollock · Sammy TinAffiliation: University of Michigan · Illinois Institute of TechnologyAbout: Microstructure · Nickel · Aerospace Engineering

Inconel 713 | Inconel 713C | IN713C | Alloy 713LC | UNS ...

Inconel 713C offers outstanding resistance to thermal fatigue and good castability while offering exceptional rupture strength at 1700°F (927°C). Inconel 713C is a nickel-chromium alloy that is ideally suited for jet engine gas turbine blades.

Engine H16BL2 – Hybl Turbines

High efficiency and durable turbine wheel from virgin Inconel 713LC alloy. Part is 100% X-ray and FPI inspected. Part is 100% X-ray and FPI inspected. Our own NGV is a highly durable integral vacuum casting from Inconel 713LC alloy for high reliability and long life.[PDF]

ADVANCED NI-BASE SUPERALLOYS FOR SMALL GAS …

technology. DS alloys are typically specified for rotating part applications, such as 2nd and 3rd stage turbine blades, where EQ alloys do not provide adequate creep strength.

Turbocharger Durability and Materials - DieselNet

Inconel 713C and its low carbon variant, 713LC, have been a common turbocharger turbine impeller wheel material for many years. These materials have good strength and creep properties to about 950°C.[PDF]

HETEROGENEITY OF INCONEL 713 LC AND INCONEL …

HETEROGENEITY OF INCONEL 713 LC AND INCONEL 738 LC ... In operational conditions of combustion turbines as part of turbo engines, blades of the circulating wheels are stressed in time, temperature and stress ... INCONEL 713LC over a section 500 μm (101 dots) ...

Nickel-based alloy casting factory - AsHelp

Inconel 713LC 738LC 718 superalloy vaccum investment casting parts America GE transportation second leave supplier, Mainly export to America/Europe/Middle east, …

Shandong Yili Power Technology Co., Ltd. - turbine wheel ...

Shandong Yili Power Technology Co., Ltd., Experts in Manufacturing and Exporting turbine wheel,impeller and 3965 more Products. A Verified CN Gold Supplier on Alibaba.[PDF]

Fatigue life of cast Inconel 713LC with/without …

Fatigue life of cast Inconel 713LC with/without protective diffusion coating under bending, torsion and their combination ESIS TC2 (Micromechanisms) Oxford, 2.4.-3.4. 2012 ... the deposition of the coating on turbine blades will lead to a longer servicePublished in: Engineering Fracture Mechanics · 2013Authors: Karel Slamecka · Karel Slamecka · Jaroslav Pokluda · Jaroslav Pokluda · Marta Kianic…Affiliation: Brno University of Technology · Central European Institute of Technology · Academy of …About: Bending · Fractography · Torsion

Hot Products

We are here to serve you!

Reply to technical consultation Provide design solution Dispatch engineers domestically/abroad Handle complaints thoroughly Systematic training Trouble judgment &amo; removal